Worm drive gearbox with motor
A robust worm-drive gearbox powered by an MM28 engine. Ideal applications where a simple to match, high torque output is required. Great for student based projects which includes robots and buggies.
The unit has been designed so that the output shaft could be ‘clicked’ in and out for modification. E.g. cutting down to size. The electric motor is snap fitted into its cradle to activate the gear and worm.
Details
1 – 6V DC
0.1A to 1A depending on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
General dimensions of box + engine: 35(W) x 40(H) x 60(L)mm
The primary feature of the high-efficiency gear box is a worm gear, which locks the output shaft whenever the engine isn’t turning. The high equipment ratios of 216:1 or 336:1 make this gearbox appropriate for little walking robots, lifting mechanisms, and other applications where high torque is certainly desired.
The low-voltage motors in the worm gearbox run on 1.5-4.5 volts and draft to some amps, making them perfect applicants for the DRV8833 motor driver carrier. Motor overheating can be due to excessive stalling, actually at very low voltages. We recommend that you utilize stall-detection sensors, or just watch your robot, to make sure that it doesn’t stall for more than a few seconds at the same time.
This gearbox includes a 4 mm diameter, round output shaft, which works together with the wheels that are appropriate for Tamiya 4 mm, round shafts. Our 3 mm universal mounting hub also suits on small threaded end of the shaft, though it is not specifically designed to work with this kind of shaft (the hub’s set screw could harm the thread on the shaft).
Ever-Power equipment motors are economical, right-angle, worm-geared motors that install easily in the tightest applications. Economical right position worm geared motors set new specifications for reliability, effectiveness and economy with unparalleled features which includes hollow shafts in the tiniest sizes. An inverter friendly design offers easy integration at this point and a truly future proof solution. The Ever-Power gear electric motor offers total flexibility in mounting choices includes shaft, base, encounter, and flange solutions. The motor terminal box can be mounted in alternate positions rotated in 90º steps around the electric motor frame providing for unparalleled integration opportunities.
Ever-Power gear motors comply with UNITED STATES and International requirements, including NEMA, IEC, CSA, and CE, the Ever-Power series permits worldwide acceptance, a genuine total alternative for our global customers.
Excellent protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dust tight and hose proof,and can be used outdoors or in wet and dusty environments without the utilization of additional enclosures. Complete rated output is available at the output shaft of the unit.
Product Features
Power rating up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Totally enclosed, sealed against dust and water spray
Lubrication change initial after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Standard), IP66 (Optional)
Additional features:
Connecting with Plug connectors.
With integrated inverter up to 7,5kW.
Ever-Power-Mark
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to EN 60034
Corrosion category predicated on DIN ISO 12944-5
C1, C2, C3, C4, C5-We, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm gear motors are the solution for applications requiring a corner turn, optional dual output, or an inability for the electric motor to be back driven. The DC correct angle equipment motors are designed for continuous and intermittent duty procedure. Our right angle equipment reducers are designed with several mounting plate options, making them well suited for a variety of DC electric motor based applications. You can expect 12 ratios ranging from 5:1 to 100:1.
10309
FEATURES
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Standard brush life of 2000+ hours (varies by application)
EP Products Worm Equipment Motors are designed to generate high torque in a small package size. Worm Equipment Motors are great for applications that require a self- locking or breaking feature since the result shaft can’t rotate when there’s no power used. Additionally, Worm Gearheads can transfer motion in 90 degrees. With various decrease ratios, precision cut gears, voltages and sizes, EP Items has a DC Worm Equipment Motor solution for your application.
Features and Benefits
HIGH Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Ability to Handle Large Gear Reduction Ratios
High Durability
Low Noise
Flexible Configuration
Applications
Security Door Locks / Industrial Conveying Systems / Security Gates / Dental Chair / Ambulance Cots & Stretchers Many of our DC Motors can be complimented with among our Worm Gearheads. EP Products will continue to work with you to create and produce a Worm Gear Electric motor that will optimize the performance of your unique application.
Built to your unique requirements
Electric motor Type: Brushed / Brushless / Coreless
Voltage
Output Speed
Power
Current
Torque
Reduction Ratio
Shaft Material & Size
Gear Material
Shaft Configuration: (D Cut / Round / Splined / Other)
Overall Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Extra Assembly Requirements (lead wires, connectors, etc.)
INTRODUCTION
The turbo metal gear worm engine runs on the metal gear box for sturdiness and a high torque output. Because of the special mechanical structure of the worm drive the electric motor output shaft is definitely self locking and can not be rotated.
This part uses a two wire connection and supports direction control and also PWM speed control. Rated voltage is 12v and will obtain 40RPM, with a torque of 8kg/cm.
SPECIFICATION
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Rated Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear products from EP DRIVESYSTEMS especially show their power in applications where high gear ratios are necessary. Our worm geared motors are consequently optimally suited for use in intralogistics, packaging technology and the meals & beverage industry.
Four great reasons for EP worm geared motors:
Rugged
Our worm geared motors have a higher overload capacity
Maintenance Friendly
Washdown versions allow simple and efficient cleaning of the drive system.
Corrosion protection
The NSD tupH sealed surface area conversion is exceptionally chemical, corrosion and abrasion resistant.
Flexibility
Our modular design give users optimum freedom.
The modular system for optimum flexibility: Our EP worm gear units
There are numerous applications that require drive systems, and each of these has its unique requirements. The EP series worm gear motors could be quickly and efficiently adapted to fulfill your needs.
Worm gear units impress with their high power density and worm motor compact design. If required, we can also supply them with the impressive nsd tupH surface treatment.
In addition to the basic EP housing, you can expect an extensive type of bolt-on elements to customize the product including torque arms, shaft covers and output flanges. These could be quickly field set up, but we will also be glad to assemble the individual components for you.
Discover more about the modular SI worm geared motors!
Find out more
Smooth and Clean: The EP worm gear unit SMI
SMI worm gear units feature a simple, corrosion-resistant alluminum alloy housing. Optional nsd tupH surface conversion makes the product ideally suited for harsh and demanding industries like meals processing and pharmaceuticals.
Flexible input designs such as for example NEMA, IEC or immediate motor mounts in extra foot or flange mounted casing designs.
Worm geared motors
Worm geared motors for small power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared motor program. The units possess on all sides different fixing possibilities and enable an easy assembling for the customer.
Additional drive configurationscan be created by use of built-on components (e.g. torque arm and result flanges). The housings are made in light weight construction out of aluminium die cast. Motor attachment is realised generally by way of IEC adapter B5 or B14A.
Technical Data
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:result shaft, result shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/mounting:uniblock, flange, torque arm
Purchase Worm Drive Gearbox with Electric motor – incorporating the following features: 1 to 6V voltage rating, 17100 rpm simply no load rate, 220g-cm stall torque, 3mm shaft diameter, 60mm long, 35mm wide, 40mm high, a robust worm drive gearbox powered by an MM28 motor (included), most ideal for applications where an easy to fit, high torque result is required, nylon housing and equipment, requires light oil or silicon grease lubrication, perfect for student based tasks including robots and buggies.
Most suitable for applications where a simple to match, high torque result is required
Perfect for student based projects including robots and buggies
Reversible High torque Turbo Worm Gear Electric motor JGY370 DC 12V 40RPM
Reversible High torque Turbo Worm Gear Motor JGY370 DC 12V 40RPM
Features:
The motor is Gear DC electric motor with micro-turbine worm, you can change the wiring-connection to improve motor rotation.
Turbo worm geared electric motor with self-lock, that is, regarding motor without electric, the output axis can be fixed, self-lock.
The reducer output shaft arranged vertically with the engine shaft, whole motor output shaft relatively-short than general gear motor, trusted to be installed the dimensions requirements strictly occasion.
Specifications:
Model: JGY370
Voltage: DC12V
No load speed: 40r/min
Output torque: 5.6kg.cm
Rated current: 0.06A
Weight: 163g
Application: open the windows, door, Mini winch. Ect.
In sumo robot or combat robot competition where high holding torque’s engine is essential to avoid your robot being pushed by your opponent robot. The worm equipment is certainly a better option when compared to spur gear motor. How come worm gear so special? Check this wiki out: Worm Drive.
“Unlike with ordinary equipment trains, the path of transmission (input shaft vs result shaft) isn’t reversible when working with large reduction ratios, because of the greater friction involved between your worm and worm-wheel, when usually a single start (1 spiral) worm is used. This can be an advantage when it’s desired to remove any possibility of the result driving the input.”
In other phrases, it is difficult to push your load (example, your robot) if the motor is not power or rotate.
Features and Spec:
Metal gear box
Result shaft is self-locking due to the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Weight: 150g