The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for employ with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you will need. For use with 5/8'' shaft sizes. Comes with set screws. More Features: Manufactured from Steel For work with with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8" to 6-3/16".
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the need to have an element bored to size, ideally lowering readily available requirements and enabling changes in shaft size if necessary. The barrel of the split tapered bushing is normally split in two spots and is usually keyed to the shaft. The barrel OD is also keyed to the travel component as well. The benefit of the split tapered bushing could it be will hold, whether or not the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.

Taper bushing are trusted together with sprockets, Split Taper Bushing china v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are created from high quality engineered supplies with wonderful tolerance. The feature is easy to employ and needs no extra alteration. These bushings can suit almost all types of assemblies and sizes. They will be the best choice in design for mechanical connections.
To complete designations add bore size. For example: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: total range of both metric and imperial offered.
Standard range meets up to 125mm/5" shafts & Hub diameter required depends upon the application.
Complete brief reach range available, for compact compact assemblies & Clean, Compact Design.
Simple installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you will need.
For use with 1 3/16'' shaft sizes.
Comes with 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2" bore is a high-quality precision product that is built for toughness and strength. U1 bushings are being used in an extensively broad range of applications, which include; sprockets, shaves, pulleys, gears, plus much more, we as well offer all of these items. What units this bushing apart is the high-quality steel development along with specific manufacturing and high quality control; this means that you always get yourself a premium quality consistent product. What really units us in addition to the other folks is our experienced expert staff members and our company-wide goal of customer satisfaction.
1. Be sure the tapered cone areas of the bushing and the within of the driven item happen to be clean and free from anti-seize lubricants.
2. Place the bushing in sprocket or various other part type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to make sure sliding in shape on shaft.
4. With key on shaft, slide the sprocket or other part type to the required job on the shaft. Make sure to leave the heads of the cap screws accessible.
5. Align the sprocket or component type, tighten the screws additionally and progressively until they are pulled up tight. Do not make use of extensions on the wrench handles and don't permit the sprocket or portion to become drawn i contact with flange of bushing. At this point there should be a gap between your bushing flange and sprocket, make certain this gap does not close.
Double split barrel ensures concentricity
Grips the shaft with positive clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key on most sizes for positive drive and increased torque carrying capabilities
Double-split barrel for confident clamping
Solid flange to maintain concentric bores
Available in ", metric, and spline bores. Bore range between 3/8" to 10"
Solid Flange & Twice Split Barrel - Assures better concentricity to the shaft.
Key to Key Drive - With keys on both the shaft and product to supply the strongest possible travel.
3/4" per Foot Taper on Barrel - Personal locking taper provides the highest degree of mechanical locking product to product.
The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for use with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you will need. For apply with 5/8'' shaft sizes. Comes with set screws. Added Features: Manufactured from Steel For make use of with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capacity from 95 to 3,000 pounds and bore sizes from 3/8" to 6-3/16".
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, ideally lowering on hand requirements and enabling changes in shaft size if required. The barrel of the split tapered bushing is usually split in two areas and can be keyed to the shaft. The barrel OD can be keyed to the travel component as well. The benefit of the split tapered bushing could it be will hold, whether or not the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.